×

Warning

JUser: :_load: Unable to load user with ID: 115637

What is the objective of an axe?
An axe has three fundamental functions. 1) Cutting 2) Splitting 3) Shaping. An axe is a incredible device that can be used with great effect, serving to you to do jobs faster and easier than ever before. There is a bit of a misconception out there that axes haven’t moved with the occasions (considerably understandable) especially when some kinds haven’t changed for decades. Nevertheless, ‘axes’ is a very broad category which consists of felling axes, tomahawks and hatchets. Each of these variations has a different objective in mind. For example a felling axe is designed for felling (fairly apparent), however a hatchet is far smaller and designed for smaller duties (still packs a big punch although!) but still can be used for larger duties if required.



Cutting Vs Splitting
The profile of the axe might be the primary part in deciding whether your axe will likely be good at cutting or splitting. How? Cutting profiles are much thinner than splitting profiles.

Why? The chopping profile is thinner because all the facility goes by means of the first level of contact (when the leading edge meets the wood), the thinner that time of contact the smaller area all of the drive is forced into. This is the same motion to shaving where the blade is really thing to chop through the hairs.

With a splitting profile though, you’ll find that the profile is wider. This more ‘wedge’ formed profile will cut up the wood into items as the log is forced two different directions.

Something to note is that chopping often goes throughout positive factors, whereas splitting goes by way of grains. When you were to try and break up a log across grains you'll find it a lot harder and less productive (that’s not even including the standard of split).

Cutting Edge: Flat Vs Rounded
Some of you may be thinking that we had forgotten to mention shaping axes in the earlier part, but don’t fear we haven’t. It's merely more applicable to speak about it here.

So although the profiles of chopping and splitting axes is completely different the cutting blade is similar style. Each of them can have rounded slicing edges. This is so that as small an space as potential makes initial contact with the wood. This makes for a much better penetration, subsequently a better cut or split.

Nevertheless, with a shaping axe, you will notice that it has a flatter slicing edge. This is so that cuts are more even relatively than a deep cut/split. With a broad axe for example you will often find one side of the bit is flat and the other ramped. This permits for clean flat section to be reduce out of the wood. You will get the flat side isn’t all the time on the one side of the axe, so make sure you get the precise side for you (usually is dependent upon your dominant hand/arm).

Bit: Single or gransfors Double
Some of you would quite a single, some a double. Each has its own deserves and drawbacks which we will attempt to make as clear as attainable for you.

The only is most positively essentially the most popular. Why? It’s simple and effective. All of the design goes into one single head. This single head is the one point of energy transfer from you to the wood being chopped. On single bit axes, you’ll typically discover that the ballot has been hardened so that it may be used as an improvised hammer. With another designs like within the tomahawk guide, you’ll additionally see some other variations made to the ballot for additional uses.

The double bit axes is less frequent, but still has a number of advantages do you have to choose them. The primary advantage looks at the balance offered due to the often symmetrical(ish) head. You’ll additionally discover (if not it’s value trying into altering) that each heads are ground differently. Why? Well like any knife, totally different grinds imply the blade might be higher suited to completely different tasks. An instance of this is a splitting and shaping leading edge or profiles for reducing and splitting.

Handle Size
You’ll find a huge range of various sized axes from the small to the huge. Very similar to how head shape is different, handle size also makes an enormous difference relying on your meant makes use of for it.

Axes measurement ranges from small ‘pocket’ axes (usually 30cm handle length) to hatchets (45 cm or so) as much as felling axes (roughly 60cm handles). Then you have axes like tomahawks and throwing axes which come in a whole array of sizes.

Bigger deal with length tends to imply more power is generated due to this fact better for bigger tasks where precision isn’t essential. If you want a axe with more control and less power then go smaller. Measurement isn’t everything, no one will decide you for having a smaller axe.
Lên trên